Simple bed frame joinery can give your bedroom a rustic but elegant look. You can do this project in your garage!
You can follow this step-by–step guide to making your own bed frame.
RELATED : Japanese Saw | Your Ultimate Guide to Japanese Saws
Joinery for Bed Frames in 10 Easy Steps
What You Really Need:
Tools
- Circular saw
- Wood chisel
- Hammer
- Power drill
- Bit set
- Caulk gun
- Framing square
- Work gloves
- Tape measure
- Safety goggles
Materials
- 3/4″ plywood sheet
- 1/4″ sheathing sheets
- 2x4x8′
- 4x4x4′
- Trim
- 8 x 1 1/4″ wood screws
- 8 x 2″ wood screws
- Caulk
- Face mask
- Wood glue
- Paint
Reminder:
Before you begin your bed frame jointery project, make sure all the materials are in stock. This will avoid any delays and ensure that you do your job quickly.
Keep a list of all materials and tools required to complete the project. Before you begin, make an inventory.
Step 1. Step 1.
You can cut the plywood board into four pieces. A table saw can be used to cut the board if you have an assistant.
You can also cut the board into sections if you prefer to do it yourself. This will make it easy for you to begin your bed frame joinery project by yourself.
Before you rip, make sure the blade is on the correct section of the cut.
All other wood pieces should be kept, except the cross-hatched ones.
Pro Tip: You can make a DIY cutting guide by using two C-clamps and a 2×4 wood. You must ensure that the wood is straight.
Step 2. Step 2.
Use a sander with 80 to 120 grit sandpaper to smoothen the surface. To make the job easier, secure the panel by using clamps.
Note:Always wear goggles when using a sander to protect your eyes against foreign substances. It is a good idea to have a first aid kit in case of an emergency with bed frame joinery.
Step 3. Step 3.
After cutting the panels, attach them to the floor. Drill three holes at the ends of each panel.
Each side panel will have 12 screws. Use wood glue and screws to attach them all at the corners.
Step 4. Step 4.
Make sure that each piece is flush with the next one. Once all the panels have been joined together, attach the gussets to each corner of the frame.
To join each side, use three screws made of wood and glue. The screw heads should be slightly recessed.
Note:Before installing the gussets on the frame, you must ensure that both sides are square. This will ensure equal frame dimensions.
Step 7. Step 7.
First, set the blade of your saw to a depth of 2”. Cut 4×4 wood into four pieces measuring 11-1/2″ each.
Notch out the back of the 4×4. This will wrap the corner of the frame, make it protrude 1 ½” at the top, and flush at the bottom section.
Begin by making a cut-out marking using a 10” line and 2’ in on both adjacent sides. Cut the 4×4 into four -long pieces.
Make two parallel cuts using the same depth of your saw blade. The small wooden piece will be attached to the drop and the cut-out corner.
Clean the inner corner with a chisel and then discard the last wood. Once done, cut the top of the 1 ½” back at an angle of 45-degrees.
Attach the corner of the interior to the mainframe with glue and nails
RELATED : Japanese Saw | Your Ultimate Guide to Japanese Saws
Step 6. Step 6.
Mount the ledger strips on the bottom of each side of the bed frame. Install the screws into the side panels using wood glue.
The distance between the sides and the frame should be used to cut seven 2x4s. When you’re done, attach the cross slats at the center.
Step 7. Step 7.
Attach the leg-mounting threads to each end of the gusset. This is only for solid legs that are threaded.
You can use nuts and washers to attach mounting threads. You can also use adhesive to replace the threads that are difficult to reach.
For the perfect and tightest fit, you can undersize by 1/16” the hole of the threaded rods. To thread the rod, rotate the leg clockwise in the wood.
Step 8: Caulk and paint the frame
Fit eight pieces of trim between each cornerpost. You will need to do this from the top to the bottom around the perimeter.
Using painter’s caulk, seal nail holes, and joints. Let dry for at most half an hour.
While waiting for the caulk to dry, cut two ¼” pieces of sheathing which go over each 2×4 crossbar.
Paint the bed frame in your choice of color once the caulk has dried.
Step 9: Let it Dry A Little More
It is best to allow the product to dry for at least 24 hours before assembling it in your room. Wood that has been exposed to direct sunlight and is not moist is best air-dried.
Are you looking for bed frame joinery ideas? SebTech DIY created this amazing video:
There are several ways to make a bedframe joinery project right. If you are looking for a simple bed frame, you will love this one. Safety first!
Loading …
Which is your favorite reason to woodwork projects yourself? We’d love to hear from you in the comments section below!
Up Next
Don’t forget to stay connected with us on Facebook, Twitter, Pinterest, and Instagram!